Linux服务器

Ubuntu IP系统配置文件使用命令设置地址

日期:2012/11/23 15:42:28来源: 绿色资源网整理

Ubuntu IP对于电脑使用的玩家的常用软件,然后我就学习及深入的研究Ubuntu IP,在这里和大家一起探讨Ubuntu IP的使用方法,希望对大家有用。Ubuntu IP地址配置.

一、使用命令设置Ubuntu IP地址

1.修改配置文件blacklist.conf禁用IPV6:sudo vi /etc/modprobe.d/blacklist.conf

2.在文档最后添加 blacklist ipv6,然后查看修改结果:cat /etc/modprobe.d/blacklist.conf

3.设置Ubuntu IP(设置网卡eth0的IP地址和子网掩码)sudo ifconfig eth0 192.168.2.1 netmask 255.255.255.0

4.Ubuntu IP设置网关sudo route add default gw 192.168.2.254

5.Ubuntu IP设置DNS 修改/etc/resolv.conf,在其中加入nameserver DNS的地址1 和 nameserver DNS的地址2 完成。

6.重启网络服务(若不行,请重启ubuntu:sudo reboot):sudo /etc/init.d/networking restart

7.查看当前Ubuntu IP:ifconfig

二、直接修改Ubuntu IP系统配置文件

Ubuntu IP的网络配置文件是:/etc/network/interfaces打开后里面可设置DHCP或手动设置静态ip。前面auto eth0,让网卡开机自动挂载。

1. 以DHCP方式配置网卡

  1. 编辑文件/etc/network/interfaces:  
  2. sudo vi /etc/network/interfaces 

并用下面的行来替换有关eth0的行:

  1. # The primary network interface - use DHCP to find our address  
  2. auto eth0  
  3. iface eth0 inet dhcp 

用下面的命令使网络设置生效:

  1. sudo /etc/init.d/networking restart 

也可以在命令行下直接输入下面的命令来获取地址sudo dhclient eth0

2. 为网卡配置静态Ubuntu IP地址

  1. 编辑文件/etc/network/interfaces:  
  2. sudo vi /etc/network/interfaces 

并用下面的行来替换有关eth0的行:

  1. # The primary network interface  
  2. auto eth0  
  3. iface eth0 inet static  
  4. address 192.168.2.1  
  5. gateway 192.168.2.254  
  6. netmask 255.255.255.0  
  7. #network 192.168.2.0  
  8. #broadcast 192.168.2.255 

将上面的Ubuntu IP地址等信息换成你自己就可以了.用下面的命令使网络设置生效:

  1. sudo /etc/init.d/networking restart 

3. 设定第二个Ubuntu IP地址(虚拟IP地址)

  1. 编辑文件/etc/network/interfaces:  
  2. sudo vi /etc/network/interfaces 

在该文件中添加如下的行:

  1. auto eth0:1  
  2. iface eth0:1 inet static  
  3. address x.x.x.x  
  4. netmask x.x.x.x  
  5. network x.x.x.x  
  6. broadcast x.x.x.x  
  7. gateway x.x.x.x 

根据你的情况填上所有诸如address,netmask,network,broadcast和gateways等信息:用下面的命令使网络设置生效:sudo /etc/init.d/networking restart

4. 设置主机名称(hostname)
使用下面的命令来查看当前主机的主机名称:sudo /bin/hostname
使用下面的命令来设置当前主机的主机名称:sudo /bin/hostname newname
系统启动时,它会从/etc/hostname来读取主机的名称。

5. 配置DNS

首先,你可以在/etc/hosts中加入一些主机名称和这些主机名称对应的IP地址,这是简单使用本机的静态查询。要访问DNS 服务器来进行查询,需要设置/etc/resolv.conf文件,假设DNS服务器的IP地址是192.168.2.2, 那么/etc/resolv.conf文件的内容应为:
search chotim.com
nameserver 192.168.2.2

6.手动重启网络服务:sudo /etc/init.d/networking restart

返回结果如下:
*Reconfiguring network interfaces… [OK]

相关文章

相关下载

网友评论

我要评论...
没有更早的评论了
取消